Achieving   Excellence   through
Diversified  Product   Solutions
 

CAT5E   Microwave   and   Accessories

CAT   5E   Weather   Resistent
The CAT 5e CMR/CMX Outdoor cable is resistant to cracking after long–term UV exposure, making it ideal for installation runs that require the cable to be exposed to the elements. This cable is listed as compliant to the 300 hour weatherometer test and –20°C cold bend test.

RJ45   Shielded   Connector
The RJ45 fully shielded plug, with an internal ground, combines the performance advantage exclusive to the RJ45 design with the performance advantage inherent to shielded products to provide an unparalleled solution for the market.

  • RJ45 design allows the wires to pass through the connector so the twists in each pair can be pulled closer to the contacts than conventional plugs.
  • Maintaining the twists to the point of termination significantly decreases crosstalk and markedly increases performance.
  • Fully shielded products provide reduced pair-to-pair crosstalk, alien crosstalk, and considerably improved immunity to noise at all frequencies.
  • Significantly improve Shannon capacity.
  • Substantially improve noise immunity at all frequencies, especially above 30 MHz when cable balance starts to significantly degrade.
 
R2CT   Housing
The kit is designed for optical systems using SFP transceivers and duplex LC-terminated fiber-optic cable. The kit uses a receptacle attached to the equipment panel and a plug assembly over the cable. The plug and receptacle use a double bayonet locking system to allow a tool less, hand-tightened connection. The plug assembly includes a protection cap that can be used for pulling cable. The R2CT kit can easily be used with other connectors and interfaces, such as RJ-45 or USB connections.

 
Miniature   Click-on   Hanger
The hangers are stackable (up to three deep) making it easy to install up to six runs of cable even in confined spaces. Miniature Click-On hangers are suitable for cable installations on tower roofs and walls or within buildings.

Cable hangers are typically used for PCS/PCN cellular microwave rural telephony GSM broadband and other telecommunications system installations. Cables are held securely in place by the gripping ribs that line the hanger's interior and eliminates the need for cable ties.

 
Lace-Up  Hoisting   Grip
The hangers are stackable (up to three deep) making it easy to install up to six runs of cable even in confined spaces. Miniature Click-On hangers are suitable for cable installations on tower roofs and walls or within buildings.

Cable hangers are typically used for PCS/PCN cellular microwave rural telephony GSM broadband and other telecommunications system installations. Cables are held securely in place by the gripping ribs that line the hanger's interior and eliminates the need for cable ties.

 
Grounding   kit
kits are designed to withstand the damaging effects of lightning currents in excess of 200kA and comply with MIL-STD-188-124A.

 
RF   Cable   and   accessories   in   building
The transmission line has an annular corrugated outer conductor and a smooth round tube center conductor.

Maximum frequency capacity is 4.9 GHz. Use AVA5-50 connectors with this standard coax cable. The Andrew 7/8 inch low loss 50 Ohm coax cable is available in bulk and is priced per foot. Part No.: 385556Cable Type: 7/8 Foam Heliax Cable Impedance (Ohms): 50 Ohms Maximum Frequency: 4.

Hardware Kit for 1/2 in or 7/8 in Double Click-on Hangers, includes 3/8 in bolts and hardware

 
Dimensions
Nominal Size 1/2 in  |  7/8 in
Length 177.80 mm  |  7.00 in
 
General Specifications
Includes Forty flat washers  |  Forty lock washers  |  Ten 3/8 in threaded rods  |  Twenty hex nuts
Maximum Stack Height 3
Package Quantity 10
 
Mechanical Specifications
Thread Size 3/4 in
 
Packed Dimensions
Height 25.4 cm  |  10.0 in
Length 8.9 cm  |  3.5 in
Shipping weight 1.36 kg  |  3.00 lb
Weight 8.9 cm  |  3.5 in
 
  • Range taking down conductor cable clamp with tower standoff.
  • Designed to attach to flat steel tower members.
  • Fast, easy and economical way to attach down conductors to flat tower members.
  • The small side of the clamp accommodates bare stranded conductors from #6 up to 2/0 AWG while the large side accommodates from 2/0 to 4/0 AWG.
  • The small side of the clamp accommodates insulated conductors from #8 up to 2/0 AWG while the large side accommodates from #1 up to 4/0 AWG.
  • Manufactured from stainless steel to allow use with any type of wire.